Nano long or short neck

Civicclutch

Civicclutch

New member
So I’m eventually soon going to get one of these. So what is the pros and cons over each one and if you have both which one do you use the most.


Sent from my iPhone using Tapatalk
 
The reach of the long neck isn’t always needed. But when you do need the extra reach it’s nice to have. That’s the only reason I chose the long over the short is because it does help occasionally.
 
Has there been a time were the long was bit to long and wish ed it was shorter


Sent from my iPhone using Tapatalk
 
I’ve never ran into that situation. I’ve had mine since they come out and use it about daily. Your better off going with the long neck. It does the same as the short neck. But gives you the extra reach on the rare occasions that you do need it.
 
I bought the long neck and have never needed the extra reach. I actually wish I would have bought the short neck because I`m sure it`s easier to use one handed.
 
Go with the long unless you are doing a lot of interior work where the shorter Ibrid helps getting into tighter spots.
 
Civicclutch said:
Has there been a time were the long was bit to long and wish ed it was shorter


Sent from my iPhone using Tapatalk
Click to expand...

long neck here.been using since they came out. never Once have I said "oh I should have bought the shorter one" but that`s just my experience
 
How many if you guys have had situations where you needed that extra in...on the neck of the ibird?? If so what were you working on? Personally I`ve never needed it.
 
DaveT435 said:
How many if you guys have had situations where you needed that extra in...on the neck of the ibird?? If so what were you working on? Personally I`ve never needed it.
Click to expand...
Just picked this up about an hour ago. Co-worker wants it coated.
Going to use the long neck under the very wide spoiler.
9dd831aaae90105532e7ad96bf4f7c51.jpg
f0da29b4a794930d848d5b1432596c7c.jpg
b997582beb71aecaeb0824bbb63ca833.jpg


Sent from my SM-G930V using Tapatalk
 
I could have sworn at release, even dylan said his choice would be the short. Something about having the better correction leverage I believe.

How tall is the nano from pad face to back of tool head?
 
WashRinseRepeat said:
Just picked this up about an hour ago. Co-worker wants it coated.
Going to use the long neck under the very wide spoiler.
9dd831aaae90105532e7ad96bf4f7c51.jpg
f0da29b4a794930d848d5b1432596c7c.jpg
b997582beb71aecaeb0824bbb63ca833.jpg


Sent from my SM-G930V using Tapatalk
Click to expand...

How far can you get under there befor the head will hit the spoiler? Is there clearance to go all the way under it?
 
2quikta said:
I could have sworn at release, even dylan said his choice would be the short. Something about having the better correction leverage I believe.

How tall is the nano from pad face to back of tool head?
Click to expand...

I`m thinking between an inch and a half and two inches. It`s personal preference. If you`re going to use it one handed you can definitely get better leverage, more consistent pressure, and better control. Just my opinion.
 
I have the short neck and can easily use it one handed. I like tools, so I wouldn’t mind getting the long neck too, but I haven’t run into a place yet where it wouldn’t reach. I’m mostly just a weekend warrior though.
 
DaveT435 said:
How far can you get under there befor the head will hit the spoiler? Is there clearance to go all the way under it?
Click to expand...
Not sure about that, I`ll be giving it a good wash tonight after work and will start polishing tomorrow after work. I`ll let you know then.

Sent from my SM-G930V using Tapatalk
 
You must log in or register to reply here.
Back
Top